En parallèle à la remise en forme de Lisa, je m'attaque à la remise en forme d'un vénérable Mac portable M5120 que Mr aurelien à eu la gentillesse de bien vouloir me céder ;o) . J'ai commandé des batteries il y a peu et je me questionne maintenant pour l'equiper d'un HD. Est ce que quelqun (tu es la fabrice ?) a deja tenter de greffer un HD standard (je sais que celui d'origine ne l'est pas) sur le bestiau ?
Autre petite question, je viens de me rendre compte que la touche "N" ne fonctionne plus (decidemment j'ai la poisse avec le "N" : idem sur le clavier de Lisa) j'espere que c'est moins chiant à reparer qu'avec le clavier de Lisa ...
Monty.
HD Pour un portable M5120
Modérateur : Politburo
- Fabrice Montupet
- Administrateur
- Messages : 11115
- Enregistré le : 17 mai 2002 11:39
- Localisation : Nevers - France
Re: HD Pour un portable M5120
La bête intègre un SCSI Conner en 34 broches. Je n'ai pas eu le temps de me construire un convertisseur pour tester la connexion a un disque dur standard SCSI 50 broches. Il faut dire que mes disques durs ont la chance de fonctionner encore, je n'ai donc pas senti l'urgence de me lancer dans sa construction. Mais j'y viendrai un jour, c'est sûr!
Voici le schéma de montage::
Source: http://antinode.info/mac/port_scsi.html
Have fin
Voici le schéma de montage::
Code : Tout sélectionner
10 March 2003. SMS.
Macintosh Portable Internal SCSI Cable
The adapter cable described in this document allows a normal SCSI
disk drive (with a normal, narrow SCSI, 50-pin connector) to be
connected to the 34-pin internal SCSI connector in a Macintosh Portable
computer. It allows the original (40MB) disk drive to be replaced by a
more readily available (and higher capacity) drive. Only a low-profile
drive will fit in the physical space, and the power requirement for the
replacement drive should be fairly close to that of the original drive,
to avoid damage to the power supply in the computer.
For example, the power rating for the 80MB Quantum ProDrive ELS (5V
230mA, 12V 135mA) is lower than that of the original 40MB Apple Hard
Disk 40SC (Conner CP-3045, 5V 275mA, 12V 250mA).
Normally, on the two-row 50-pin connector, odd pins 1-23 and 27-49
are ground, and pin 25 is not connected. In this adapter cable, the
connections 2-47, 6-49, 11-39, and 16-5, are opportunistic grounds, easy
to make with paired conductors in the 34-conductor ribbon cable.
Attach the 34-pin connector to the ribbon cable last, as this makes
it easier to get the cable length correct.
SCSI 34-pin 50-pin
TERMPWR NC 26
-REQ 1 48 \ pair
(gnd) 2 47 (gnd) /
-MSG 3 42
-C/D 4 46
-I/O 5 50 \ pair
(gnd) 6 49 (gnd) /
-ACK 7 38
-ATN 8 32
-BSY 9 36
-RST 10 40 \ pair
(gnd) 11 39 (gnd) /
-SEL 12 44
-DB(P) 13 18
-DB(0) 14 2
-DB(1) 15 4 \ pair
(gnd) 16 5 (gnd) /
-DB(2) 17 6
-DB(3) 18 8
-DB(4) 19 10
-DB(5) 20 12
-DB(6) 21 14
-DB(7) 22 16
5V pwr 23 -----+ 12 0 0 5
5V pwr 24 -----+ /------------\
12V pwr 25 ---+ | / \
12V pwr 26 ---+ | | o o o o |
0V pwr 27 -+ | | | |
0V pwr 28 -+ | | +----------------+
0V pwr 29 -+ | | Y B B R
0V pwr 30 -+ | |
12V pwr 31 ---+ | Female power connector, as viewed
12V pwr 32 ---+ | from the disk drive. (Typical wire
5V pwr 33 -----+ colors are Yellow, Black, and Red.)
5V pwr 34 -----+
Signal lines in sequence for the 50-pin connector.
SCSI 34-pin 50-pin
-DB(0) 14 2
-DB(1) 15 4 \ pair
(gnd) 16 5 (gnd) /
-DB(2) 17 6
-DB(3) 18 8
-DB(4) 19 10
-DB(5) 20 12
-DB(6) 21 14
-DB(7) 22 16
-DB(P) 13 18
20 (gnd)
22 (gnd)
24 (gnd)
TERMPWR 26
28 (gnd)
30 (gnd)
-ATN 8 32
34 (gnd)
-BSY 9 36
-ACK 7 38
(gnd) 11 39 (gnd) \ pair
-RST 10 40 /
-MSG 3 42
-SEL 12 44
-C/D 4 46
(gnd) 2 47 (gnd) \ pair
-REQ 1 48 /
(gnd) 6 49 (gnd) \ pair
-I/O 5 50 /
Change notice: In a previous version of this document, the connection
to pin 5 on the 50-pin connector was made to pin 3, instead. The
function (ground) is the same, but using pin 5 makes the wire order a
bit nicer.
Have fin
-
- Fonctionne à 300 bauds
- Messages : 206
- Enregistré le : 05 juil. 2010 23:06
- Localisation : Haute-Savoie
Re: HD Pour un portable M5120
Thanks a lot sir !